Buyer guide
550 W solar panel dimensions: size, weight and container loading
2,278 x 1,134 mm and 27.5 kg decide your racking, your string length and your container count. The numbers, model by model, and what they mean on site.
A 550 W module in 2026 is almost always 2,278 mm long, 1,134 mm wide and 30 mm deep — the 144-half-cell format built on 182 mm wafers. Those numbers decide more of your project than the nameplate: how many modules fill a roof row, how many fit a 40-foot container, and whether two installers can lift one onto a rail. Here are the dimensions we publish for our own modules, and what they do to a layout.
The standard 550 W footprint
2,278 x 1,134 mm gives 2.58 m2 of aperture. Divide 550 W by it and you get 213 W/m2 — the 21.3 % efficiency on the datasheet, and a useful cross-check, because no mass-produced module beats 24 % at module level. A 550 W panel much smaller than 2.4 m2 does not exist.
Watch the exception: some factories reach 550 W from 210 mm cells at up to 2.4 x 1.1 m. The wattage matches, the drawing does not, and racking cut to the wrong drawing is expensive. Ask for the outline drawing, not just the datasheet.
Dimensions and weight, model by model
| Model | Rated power | L x W x frame (mm) | Area | Weight | Cells |
|---|---|---|---|---|---|
| GH-SPM-550M | 550 W | 2278 x 1134 x 30 | 2.58 m2 | 27.5 kg | 144 half, 182 mm |
| GH-SPT-580N | 580 W | 2278 x 1134 x 30 | 2.58 m2 | 28.0 kg | 144 half, 182 mm |
| GH-SPB-555N | 555 W | 2278 x 1134 x 30 | 2.58 m2 | 32.0 kg | 144 half, dual glass |
| GH-SPH-700H | 700 W | 2384 x 1303 x 35 | 3.11 m2 | 38.0 kg | 132 half, 210 mm |
The 550 W PERC module and the 580 W TOPCon module share one footprint. N-type cells convert more of the same area, so upgrading a fixed roof adds kWp without touching the racking layout.
What it means on a roof
At 1,134 mm wide the module fits the four-row layouts most commercial roofs are designed around, with the mid-clamp inside the 300-400 mm clamp zone from the frame corner. In landscape, two modules span 4.55 m — a 4.4 m rafter spacing plus the overhang the wind calculation expects.
Portrait mounting puts the rails at the quarter and three-quarter points of the 2,278 mm length; landscape on an exposed site needs three rails. Either way, the 200-400 mm roof-edge setback usually costs you a column of modules before the electrical design starts.
Weight, and what the roof has to carry
A framed monofacial 550 W module weighs about 27.5 kg; the dual-glass bifacial version of the same size about 32 kg. With rails and clamps the dead load lands near 12 kg/m2, against the 5400 Pa snow and 2400 Pa wind load the module is tested to under IEC 61215.
27.5 kg is a two-person lift with a suction cup and no crane. The 700 W class, at 38 kg and 2.38 m long, is a different job — and some racking is simply not rated for its larger wind area.
String design: 20 modules is the ceiling
The 550 W module has a Voc near 49.9 V and a temperature coefficient of -0.27 %/C, which becomes 54.6 V per module at -10 C. On a 1,000 V MPPT that caps a string at 18 modules (983 V); on a 1,100 V input, 20 modules (1,092 V) is the limit. Short-circuit current of about 14 A puts 1.5 x Isc sizing on 4 mm2 or 6 mm2 string cable.
Container loading: 620 modules, 341 kWp
This is where dimensions beat watts. A 40HQ takes 620 modules of the 550 W class, which is 341 kWp of nameplate capacity. The load weighs about 17 tonnes before packaging, 18 tonnes packed, against a payload allowance near 26 tonnes — the container is volume-limited, not weight-limited. A heavier dual-glass module does not cut the count; a longer 700 W module does, and kWp per container drops.
Ask for the loading plan with the quotation: pallet count, stack height, axle weight distribution and modules per pallet. That is what your broker and your installation schedule actually need.
What to ask a supplier for
- Outline drawing — frame thickness, clamp zones, junction box position.
- Flash-test data for the actual pallet: 0/+5 W sorting means nothing ships below nameplate, but you should still see the measured watts.
- Weight per pallet and per container, for crane and site-access planning.
- Loading plan and packing list keyed to pallet IDs.
Dimensions, weight and ex-works price are published for every model in the mono PERC range, the TOPCon range and the bifacial dual-glass range — the 550 W class appears in all three.
Frequently asked questions
What are the dimensions of a 550 W solar panel?
2278 x 1134 x 30 mm for the 144-half-cell 182 mm format: 2.58 m2 and 21.3 % efficiency. Some factories build 550 W from 210 mm cells at up to 2.4 x 1.1 m, so check the outline drawing before ordering racking.
How much does a 550 W solar panel weigh?
About 27.5 kg framed monofacial and 32 kg for the dual-glass bifacial version of the same size. Both are two-person lifts; the 38 kg, 2.38 m 700 W class needs a lifting plan.
How many 550 W solar panels fit in a 40ft container?
620 modules, which is 341 kWp. The load runs about 18 tonnes packed against a payload allowance near 26 tonnes — volume-limited, so a heavier module does not reduce the count but a longer one does.